The RF300 comes with a pre-installed cable that links to your autopilot computer (e.g., AC12 or AC42).
Ensure the distance from the rudder post center to the ball joint (Y1) is equal to the distance from the RF300 center to its transmitter rod connection (Y2).
Mount the RF300 on a suitable platform where its center is directly in line with the center of the rudder post.
Inspect the ball joints every six months for wear or corrosion.
Probe the Brown and White lines while the unit is powered by the autopilot computer. At exact midships, you should read approximately .
Ultimate Simrad RF300 Installation Guide: Step-by-Step Rudder Feedback Setup
: Set the helm wheel to the center position. Rotate the RF300 transmitter lever until it aligns with the center mark, which should be opposite the cable entry.
A: The RF300 is a precision rudder feedback sensor. It provides real-time rudder angle data to your autopilot computer, enabling the system to steer your boat accurately and maintain the course you set.
| Pin | Wire Color | Signal | |-----|------------|------------| | 1 | Shield | Drain | | 2 | Red | +12V DC | | 3 | Black | Ground | | 4 | White | CAN High (H) | | 5 | Blue | CAN Low (L) |
Whether you are replacing an old unit or installing a completely new autopilot system, mounting and wiring the RF300 correctly prevents steering overshoots, pilot drifting, and unnecessary strain on your hydraulic or mechanical steering system.
The RF300 must be mounted in the steering compartment, close to the rudder tiller arm.
Verify that the base mounting screws remain tight against the hull.
The is not merely a pamphlet of warnings and diagrams—it is the definitive guide to ensuring that your autopilot system has accurate, real-time rudder position data. By following the mechanical, electrical, and calibration steps outlined above, and by respecting the nuances that only real-world experience (like this article) can provide, you will achieve a professional-grade installation.
: Mount the RF300 on a stable platform where its center is perfectly in line with the center of the rudder post. Mechanical Linkage : The unit comes with a transmission link assembly.
Are you installing this as part of a or replacing a faulty unit on an existing setup? INSTALLATION REV A Instruction Manual Page 72
The RF300 comes with a pre-installed cable that links to your autopilot computer (e.g., AC12 or AC42).
Ensure the distance from the rudder post center to the ball joint (Y1) is equal to the distance from the RF300 center to its transmitter rod connection (Y2).
Mount the RF300 on a suitable platform where its center is directly in line with the center of the rudder post.
Inspect the ball joints every six months for wear or corrosion. simrad rf300 installation manual
Probe the Brown and White lines while the unit is powered by the autopilot computer. At exact midships, you should read approximately .
Ultimate Simrad RF300 Installation Guide: Step-by-Step Rudder Feedback Setup
: Set the helm wheel to the center position. Rotate the RF300 transmitter lever until it aligns with the center mark, which should be opposite the cable entry. The RF300 comes with a pre-installed cable that
A: The RF300 is a precision rudder feedback sensor. It provides real-time rudder angle data to your autopilot computer, enabling the system to steer your boat accurately and maintain the course you set.
| Pin | Wire Color | Signal | |-----|------------|------------| | 1 | Shield | Drain | | 2 | Red | +12V DC | | 3 | Black | Ground | | 4 | White | CAN High (H) | | 5 | Blue | CAN Low (L) |
Whether you are replacing an old unit or installing a completely new autopilot system, mounting and wiring the RF300 correctly prevents steering overshoots, pilot drifting, and unnecessary strain on your hydraulic or mechanical steering system. Inspect the ball joints every six months for
The RF300 must be mounted in the steering compartment, close to the rudder tiller arm.
Verify that the base mounting screws remain tight against the hull.
The is not merely a pamphlet of warnings and diagrams—it is the definitive guide to ensuring that your autopilot system has accurate, real-time rudder position data. By following the mechanical, electrical, and calibration steps outlined above, and by respecting the nuances that only real-world experience (like this article) can provide, you will achieve a professional-grade installation.
: Mount the RF300 on a stable platform where its center is perfectly in line with the center of the rudder post. Mechanical Linkage : The unit comes with a transmission link assembly.
Are you installing this as part of a or replacing a faulty unit on an existing setup? INSTALLATION REV A Instruction Manual Page 72